How quickly can cantilever rack be delivered and installed in Romeoville?

Our Westmont warehouse is about 25 minutes from Romeoville, so standard components often arrive within 48 hours of an approved order. Engineered cantilever rack parts can take longer, and we put the real lead time in writing with your quote. Most Romeoville installations run one to four weeks depending on size.

Does cantilever rack work in Romeoville buildings near I-55 Weber Road interchange?

Usually, yes. In Romeoville, newer big-box distribution centers with tall clear heights next to older Joliet Road industrial buildings. We plan the cantilever rack around your column grid, clear height, and dock layout so load positions land where the building allows, and we show you the position count before you order.

Which Romeoville operations get the most out of cantilever rack?

We see it pay off most for retail distribution and third-party logistics operations in Romeoville, especially where lumber or pipe stacked on the floor and blocking work areas is the daily headache. During a free warehouse consultation we compare cantilever rack with other options for your SKUs so you can see whether it is the right fit.

How much weight can each arm carry?

Arm capacity is specified per arm and per column, based on your heaviest bundle and how far the load projects. Give us bundle dimensions and weights and we size arms, columns, and bracing to that with margin - then hand over the ratings for the finished run.

How far apart should the columns be?

Close enough that the load doesn't sag between arms. A common starting point puts arm spacing at roughly half the load length, with the remainder overhanging each end evenly. We check that math against your heaviest bundle before finalizing spacing.

Will our forklift or side loader work with a cantilever layout?

Aisle width and arm clearance are matched to whatever is moving material - standard forks, a side loader, or an overhead crane. Tell us the equipment and its turning or reach dimensions and the layout gets built around it.

Can arms or levels be added later?

Yes. Arms mount at set increments up the column, so levels can be added or repositioned as your product mix shifts, as long as total load stays within the rated capacity of the column and base.

Cantilever Rack system inside a Illinois warehouse

Romeoville, Illinois

Cantilever Rack for Romeoville, Illinois Warehouses

Name: Chicago Pallet Racks - Romeoville
Address: 36 N. Cass Ave., Westmont, IL, 60559, US
Telephone: (312) 815-2445
Price range: $$

A lot of the calls we get from Romeoville start the same way: a newer big-box building off Weber Road with plenty of height but rack that only uses half of it. Underneath that is usually lumber or pipe stacked on the floor and blocking work areas, and it gets worse every month the layout stays the same.

Cantilever rack holds lumber, pipe, tubing, and sheet goods on arms with no front column in the way, so long loads come off the floor and onto rated levels. Before anything is ordered, your Romeoville team gets a drawing, a position count, and a line-item price, so the decision is based on numbers. Call (312) 815-2445 to start a free layout.

(312) 815-2445

Why Romeoville Warehouses Work With Us

Warehouses near the Lewis University Airport area and the Airport Road distribution parks each come with their own limits: usable height, column spacing, dock count. In Romeoville, newer big-box distribution centers with tall clear heights next to older Joliet Road industrial buildings, so we draw every cantilever rack layout to the actual building.

Our team has quoted and installed racking for retail distribution and third-party logistics work in Romeoville for decades. With cantilever rack, the deciding factor is normally arms repositioned as your product lengths change, and we put the numbers for that in front of you up front.

Being about 25 minutes away in Westmont, with I-55, Weber Road, and Route 53 between us, keeps delivery windows tight and replacement parts on hand. Installation is done by our own crews, and your Romeoville layout stays on file for the next expansion.

Free warehouse consultation

CAD layout with position counts

Installation by our own crews

Cantilever warehouse racking holding steel tubing

Cantilever rack storing lumber and wood products

Operations We Rack Around Here

Nearby areas we work in regularly include the I-55 Weber Road interchange, the Lewis University Airport area, the Joliet Road industrial parks, the Airport Road distribution parks.

Retail distribution

Third-party logistics

Food & beverage

Consumer goods

How Cantilever Rack Works

Arms with nothing in front of them, built for lumber, pipe, and anything a pallet can't hold.

Columns and anchored bases

Upright columns sit on anchored bases. Base depth is set by load and arm length so the run stays stable even under an off-center pick.

Arms at adjustable heights

Arms bolt or pin into the column at set increments and move as your product mix changes. Straight arms suit boxed goods; inclined arms with a lip hold round or loose stock in place.

Column spacing against sag

Spacing between columns is set so bundles don't sag between arms. A common starting rule places arms about half the load length apart, with the ends overhanging evenly.

Single-sided or double-sided

Single-sided runs go against a wall. Double-sided runs stand in open floor and load from both faces, doubling capacity per base without doubling the footprint.

What a Cantilever Rack Project Includes

Before cantilever rack is priced for your Romeoville building, we gather the constraints: usable height, column grid, aisle widths your lifts need, SKU count, and the load mix your retail distribution volume actually moves. Most of that comes from one phone conversation.

The deliverable is a CAD layout and a priced bill of material: positions, elevations, aisle widths, and capacities. Since long material off the floor and back into usable positions drives the design, we often model the same Romeoville footprint two ways so you can weigh density against picking speed with real figures.

Common cantilever rack parts move from our Westmont stock within days. Our crews install to the approved drawing, anchor every frame, and work around your shifts so third-party logistics production does not stop. Your layout stays on file, so adding a bay next year or replacing a damaged upright starts from where the system already is.

Lumber, plywood, and sheet goods

Pipe, tube, conduit, and bar stock

Steel service center inventory

Furniture, doors, and windows

Long or awkward loads currently sitting on the floor

Call (312) 815-2445

Recent Installations

Racking projects completed for warehouses across Chicago and the surrounding suburbs.

Carton flow rack installation in a warehouse

Drive-in pallet rack installation in a high-bay warehouse

Pallet rack installation reaching the ceiling of a distribution center

Selective pallet rack aisle with wire decking

Warehouse pallet racking aisles with a forklift

Rows of pallet racking in a distribution facility

Warehouse pallet rack system spanning a large storage area

Pallet racking rows under warehouse skylights

Cantilever rack arms mounted along a warehouse wall

Push back pallet rack carts on inclined rails

View More Projects

Get a Cantilever Rack Quote for Your Romeoville Warehouse

Send the basics and we will follow up with a layout and pricing. Prefer to talk it through? Call (312) 815-2445.

Chicago Pallet Racks

36 N. Cass Ave.

Unit #5170

Westmont, IL 60559

(312) 815-2445

Monday - Friday: 8:00 AM - 6:00 PM

Name *

Company *

Email *

Phone *

Where are you located? *

Approximate warehouse size *

Expected timeframe *

Additional Information

I consent to receive SMS and email communications from Chicago Pallet Racks regarding my quote request. Message and data rates may apply. Reply STOP to opt out.

We respect your privacy. Your information will never be shared.