How quickly can cantilever rack be delivered and installed in Chicago?

Our Westmont warehouse is about 35 minutes from Chicago, so standard components often arrive within 48 hours of an approved order. Engineered cantilever rack parts can take longer, and we put the real lead time in writing with your quote. Most Chicago installations run one to four weeks depending on size.

Does cantilever rack work in Chicago buildings near Kinzie Industrial Corridor?

Usually, yes. In Chicago, older multi-story brick buildings with tight column grids and freight elevators sit a few miles from newer single-story boxes with 32-foot clear heights. We plan the cantilever rack around your column grid, clear height, and dock layout so load positions land where the building allows, and we show you the position count before you order.

Which Chicago operations get the most out of cantilever rack?

We see it pay off most for food & beverage distribution and third-party logistics operations in Chicago, especially where bundle lengths that do not fit a standard pallet rack bay is the daily headache. During a free warehouse consultation we compare cantilever rack with other options for your SKUs so you can see whether it is the right fit.

How much weight can each arm carry?

Arm capacity is specified per arm and per column, based on your heaviest bundle and how far the load projects. Give us bundle dimensions and weights and we size arms, columns, and bracing to that with margin - then hand over the ratings for the finished run.

How far apart should the columns be?

Close enough that the load doesn't sag between arms. A common starting point puts arm spacing at roughly half the load length, with the remainder overhanging each end evenly. We check that math against your heaviest bundle before finalizing spacing.

Will our forklift or side loader work with a cantilever layout?

Aisle width and arm clearance are matched to whatever is moving material - standard forks, a side loader, or an overhead crane. Tell us the equipment and its turning or reach dimensions and the layout gets built around it.

Can arms or levels be added later?

Yes. Arms mount at set increments up the column, so levels can be added or repositioned as your product mix shifts, as long as total load stays within the rated capacity of the column and base.

Cantilever Rack system inside a Illinois warehouse

Chicago, Illinois

Cantilever Rack in Chicago, IL

Name: Chicago Pallet Racks - Chicago
Address: 36 N. Cass Ave., Westmont, IL, 60559, US
Telephone: (312) 815-2445
Price range: $$

Freight stacked in the aisles of an older brick building because the floor was never laid out for modern pallet loads is one of the most common problems we see in Chicago right now. Look closer and the real issue tends to be bundle lengths that do not fit a standard pallet rack bay.

Cantilever rack holds lumber, pipe, tubing, and sheet goods on arms with no front column in the way, so long loads come off the floor and onto rated levels. We work out the storage math for your Chicago footprint first, then hand you a CAD layout and itemized quote before a single beam ships. Call (312) 815-2445 to get started.

(312) 815-2445

Why Chicago Warehouses Work With Us

Warehouses near Pilsen and the Lower West Side and the Clearing district near Midway each come with their own limits: usable height, column spacing, dock count. In Chicago, older multi-story brick buildings with tight column grids and freight elevators sit a few miles from newer single-story boxes with 32-foot clear heights, so we draw every cantilever rack layout to the actual building.

Our team has quoted and installed racking for food & beverage distribution and third-party logistics work in Chicago for decades. With cantilever rack, the deciding factor is normally single-sided runs along the wall, double-sided in open floor, and we put the numbers for that in front of you up front.

Our Westmont warehouse is about 35 minutes from Chicago by way of I-55, I-90/94, and I-290, so deliveries are short, parts are close, and our own crews do the installation. One contact handles the layout, quote, schedule, and service afterward.

Free warehouse consultation

CAD layout with position counts

Installation by our own crews

Cantilever warehouse racking holding steel tubing

Cantilever rack storing lumber and wood products

Operations We Rack Around Here

Nearby areas we work in regularly include the Kinzie Industrial Corridor, Pilsen and the Lower West Side, the Stevenson corridor, the Clearing district near Midway.

Food & beverage distribution

Third-party logistics

E-commerce fulfillment

Printing & packaging

How Cantilever Rack Works

Arms with nothing in front of them, built for lumber, pipe, and anything a pallet can't hold.

Columns and anchored bases

Upright columns sit on anchored bases. Base depth is set by load and arm length so the run stays stable even under an off-center pick.

Arms at adjustable heights

Arms bolt or pin into the column at set increments and move as your product mix changes. Straight arms suit boxed goods; inclined arms with a lip hold round or loose stock in place.

Column spacing against sag

Spacing between columns is set so bundles don't sag between arms. A common starting rule places arms about half the load length apart, with the ends overhanging evenly.

Single-sided or double-sided

Single-sided runs go against a wall. Double-sided runs stand in open floor and load from both faces, doubling capacity per base without doubling the footprint.

What a Cantilever Rack Project Includes

Every cantilever rack project in Chicago begins with the numbers: what you store, how heavy it is, what lifts it, and how tall the usable space is. We collect those during a free warehouse consultation by phone, along with a floor plan or a few photos if you have them.

The deliverable is a CAD layout and a priced bill of material: positions, elevations, aisle widths, and capacities. Since arm length and capacity set by the bundles you handle drives the design, we often model the same Chicago footprint two ways so you can weigh density against picking speed with real figures.

Common cantilever rack parts move from our Westmont stock within days. Our crews install to the approved drawing, anchor every frame, and work around your shifts so third-party logistics production does not stop. Your layout stays on file, so adding a bay next year or replacing a damaged upright starts from where the system already is.

Lumber, plywood, and sheet goods

Pipe, tube, conduit, and bar stock

Steel service center inventory

Furniture, doors, and windows

Long or awkward loads currently sitting on the floor

Call (312) 815-2445

Recent Installations

Racking projects completed for warehouses across Chicago and the surrounding suburbs.

Carton flow rack installation in a warehouse

Drive-in pallet rack installation in a high-bay warehouse

Pallet rack installation reaching the ceiling of a distribution center

Selective pallet rack aisle with wire decking

Warehouse pallet racking aisles with a forklift

Rows of pallet racking in a distribution facility

Warehouse pallet rack system spanning a large storage area

Pallet racking rows under warehouse skylights

Cantilever rack arms mounted along a warehouse wall

Push back pallet rack carts on inclined rails

View More Projects

Get a Cantilever Rack Quote for Your Chicago Warehouse

Send the basics and we will follow up with a layout and pricing. Prefer to talk it through? Call (312) 815-2445.

Chicago Pallet Racks

36 N. Cass Ave.

Unit #5170

Westmont, IL 60559

(312) 815-2445

Monday - Friday: 8:00 AM - 6:00 PM

Name *

Company *

Email *

Phone *

Where are you located? *

Approximate warehouse size *

Expected timeframe *

Additional Information

I consent to receive SMS and email communications from Chicago Pallet Racks regarding my quote request. Message and data rates may apply. Reply STOP to opt out.

We respect your privacy. Your information will never be shared.